How to Start a Pontiac G6 Without a Key: A Step-By-Step Guide

Introduction

The Pontiac G6 is a mid-size car that was produced by General Motors from 2005 to 2010. It was available as a four-door sedan, two-door coupe, and five-door hatchback. The G6 was known for its stylish design and comfortable interior, making it a popular choice among consumers.

However, what happens if you find yourself in a situation where you don’t have a key to start your Pontiac G6? You may be tempted to panic, but don’t worry—there are several ways to start your G6 without a key. In this article, we’ll explore these methods and provide step-by-step instructions so you can get back on the road in no time.

Using a Slim Jim to Access the Lock

A slim jim is a tool used by locksmiths to access locked vehicles. It works by slipping the slim jim between the weather stripping and window of the door, then manipulating the lock mechanism to open the door. While it is possible to use a slim jim to open the door of your Pontiac G6, it should only be attempted by someone with experience.

If you decide to use a slim jim, here are the steps you should follow:

• Locate the weather stripping along the edge of the door.
• Slide the slim jim between the weather stripping and the window.
• Manipulate the lock mechanism until the door opens.
• Once the door is open, use a screwdriver to remove the screws holding the panel in place.
• Pull off the panel to expose the ignition switch.
• Attach a wire to the positive terminal of the battery and touch the other end to the positive terminal of the ignition switch.
• Turn the key in the ignition and the car should start.

Installing an Aftermarket Push Button Ignition

If you don’t feel comfortable using a slim jim, you can also install an aftermarket push button ignition. This method requires some mechanical knowledge, but it is relatively simple. Here’s how it works:

• Purchase an aftermarket push button ignition kit for your Pontiac G6.
• Disconnect the negative cable from the battery.
• Remove the existing ignition switch.
• Install the aftermarket push button ignition in its place.
• Connect the wiring harness from the aftermarket ignition to the car’s wiring.
• Reconnect the negative cable to the battery.
• Test the push button ignition to make sure it works properly.

Jump Starting the Pontiac G6

If you don’t have a key and don’t want to install an aftermarket ignition, you can jump start your Pontiac G6. To do this, you will need another vehicle with a functional battery. Here’s how it’s done:

• Park the other vehicle close to your Pontiac G6.
• Connect jumper cables to the battery of the other vehicle.
• Connect one of the cables to the positive terminal of the Pontiac G6’s battery.
• Connect the remaining cable to the negative terminal of the Pontiac G6’s battery.
• Start the other vehicle and let it run for a few minutes.
• Try to start the Pontiac G6. If it doesn’t start, try again.

Programming a New Key Fob

If you don’t have a key but do have a key fob, you can program it to start your Pontiac G6. To do this, you will need a blank key fob and a key programming tool. Here’s how it’s done:

• Insert the blank key fob into the key programming tool.
• Follow the instructions on the key programming tool to program the key fob.
• Once the key fob is programmed, insert it into the ignition and turn the key.
• The Pontiac G6 should start.

Replacing the Door Lock Cylinder

If you don’t have a key or a key fob, you can replace the door lock cylinder with a new one. To do this, you will need a new door lock cylinder, a screwdriver, and a pair of pliers. Here’s how it’s done:

• Open the door of the Pontiac G6 and locate the door lock cylinder.
• Use a screwdriver to remove the screws holding the door lock cylinder in place.
• Use a pair of pliers to remove the old door lock cylinder.
• Insert the new door lock cylinder and secure it with the screws.
• Insert the key into the door lock cylinder and turn it to unlock the door.
• Insert the key into the ignition and turn it to start the car.

Utilizing a Professional Locksmith

If all else fails, you can always hire a professional locksmith to help you start your Pontiac G6. A locksmith can use specialized tools to open the door and start the car without damaging it. Here’s how it works:

• Contact a professional locksmith and explain your situation.
• The locksmith will arrive at your location with the necessary tools.
• The locksmith will use their tools to open the door and start the car.
• Once the car is started, the locksmith will provide you with a new key.

Conclusion

Starting a Pontiac G6 without a key may seem daunting, but it doesn’t have to be. With the right tools and knowledge, you can get your car running in no time. Whether you choose to use a slim jim, install an aftermarket push button ignition, jump start the car, program a new key fob, replace the door lock cylinder, or utilize a professional locksmith, you can be sure that your G6 will be up and running in no time.